manualshive.com logo in svg

Allen-Bradley 1732ES-IB12XOB4, User Manual, Page: 90 / 176

Share
Download
Allen-Bradley 1732ES-IB12XOB4 User Manual Download Page 90

90

Rockwell Automation Publication 1791ES-UM001G-EN-P - November 2016

Chapter 5

Configure the I/O Modules

• Standard - Safety input has a standard field device that is wired to it

4. Complete entries, and note the following:

• For each safety input on the module, you can define if the input is 

pulse tested. If the inputs are pulse tested, select which test source to 
use.

• Off -> On and On -> Off delay times can be configured per channel 

with each channel tuned to match the characteristics of the field 
device for maximum performance.

• Input Error Latch Time is the time that the module holds an error to 

make sure that the controller can detect it. This setting provides you 
more reliable diagnostics and enhances the chances that a nuisance 
error is detected.

5. Click OK at the bottom of the dialog box or a tab at the top of the dialog 

box.

Configure the Test Outputs

Table 24

 provides information for configuring the test outputs.

 

Follow these steps to configure the test outputs.

1. Click the Test Outputs tab.

 

Table 24 - Configuring Test Outputs

Parameter Name

Value

Description

Default

Test Output Mode

Not Used

The test output is disabled.

Not Used

Standard

The output point is enabled for use by the GuardLogix controller.

Pulse Test

The test output is being used as a pulse test source.

Power Supply

A constant 24V is placed on the output terminal. It can be used to provide power to a field device.

Muting Lamp Output 

(1)

An indicator lamp is connected to the output. When this lamp is energized, a burned-out bulb, broken 
wire, or short to GND error condition can be detected. Typically, the lamp is an indicator that is used in 
light curtain applications.

(1) Terminal T3/T7 for 1791ES-IB8XOBV4, 1732ES-IB8XOB8 and 1732ES-IB8XOBV4 modules, terminal T3/T7/T11/T15 for 1791ES-IB16 and 1732ES-IB16 modules, and terminal T3/T7/T11 for 

1732ES-IB12XOB4 and 1732ES-IB12XOBV2 modules.

Summary of Contents for 1732ES-IB12XOB4

















































































































































































Reviews:

No comments