manualshive.com logo in svg

Allen-Bradley 1732ES-IB12XOB4, User Manual, Page: 33 / 176

Share
Download
Allen-Bradley 1732ES-IB12XOB4 User Manual Download Page 33

Rockwell Automation Publication 1791ES-UM001G-EN-P - November 2016

33

About the Modules

Chapter 2

Selecting a Power Supply

For CE LVD compliance, verify that the external power supply that provides 
power to the modules is safety extra low voltage (SELV) rated. Some Rockwell 
Automation® Bulletin 1606 power supplies are SELV-compliant. See Switched 
Mode Power Supply Specifications Technical Data, publication 

1606-TD002

, 

and the installation instructions for the modules.

Table 6 - Guard I/O Module Descriptions

Catalog Number

Description

Enclosure Type 
Rating

Safety Inputs Test Outputs

(1)

Safety Outputs (solid-state)

1791ES-IB16

CompactBlock™ safety input module

Meets IP20

16

16

—

1791ES-IB8XOBV4

CompactBlock safety I/O module with solid-state outputs

8

8

8 bipolar outputs (4 pairs)

1732ES-IB12XOB4

ArmorBlock® safety I/O module with solid-state outputs

Meets IP65/IP67 
(when marked)

12

12

4 sourcing outputs

1732ES-IB12XOBV2

ArmorBlock safety I/O module with solid-state outputs

12

12

4 bipolar outputs (2 pairs)

1732ES-IB16

ArmorBlock safety input module

Meets IP65/IP67 
(when marked)

16

16

—

1732ES-IB8XOB8

ArmorBlock safety I/O module with solid-state outputs

Meets IP65/IP67 
(when marked)

8

8

8  sourcing  outputs

1732ES-IB8XOBV4

ArmorBlock safety I/O module with solid-state outputs

Meets IP65/IP67 
(when marked)

8

8

8 bipolar outputs (4 pairs)

(1) Broken wires can be detected on the muting outputs.

ATTENTION: 

Prevent Electric Shock

To prevent electric shock, use a DC power supply that meets the following 
requirements:

• A DC power supply with double or reinforced insulation; for example, 

according to IED/EN 60950, or EN 50178, or a transformer according to 
IEC/EN 61558.

• A DC power supply satisfies requirement for class 2 circuits or limited 

voltage/current circuit stated in UL 508.

• An external power supply that is safety extra-low voltage (SELV) rated.

ATTENTION: 

Do Not Exceed Specified Voltage

• Do not apply DC voltages exceeding the rated voltages to the module.

• Apply properly specified voltages to the module inputs. Applying 

inappropriate voltages causes the module to fail to perform its specified 
function, which leads to loss of safety functions or damage to the module.

Summary of Contents for 1732ES-IB12XOB4

















































































































































































Reviews:

No comments