Allen-Bradley 1732ES-IB12XOB4 User Manual Download Page 141

Page: 141 / 176

Rockwell Automation Publication 1791ES-UM001G-EN-P - November 2016

141

Get Diagnostic Status from Modules by Using Explicit Messaging

Appendix A

334 (820)

Safety and
standard

Safety Input 7

Safety Input 6

Safety Input 5

Safety Input 4

Safety Input 3

Safety Input 2

Safety Input 1

Safety Input 0

Safety Input 7
Status

Safety Input 6
Status

Safety Input 5
Status

Safety Input 4
Status

Safety Input 3
Status

Safety Input 2
Status

Safety Input 1
Status

Safety Input 0
Status

Reserved

Input Power
Error

(1)

Output Power
Error

(1)

Reserved

Muting Lamp 7
Status

Muting Lamp 3
Status

344 (836)

Safety and
standard

Safety Input 7

Safety Input 6

Safety Input 5

Safety Input 4

Safety Input 3

Safety Input 2

Safety Input 1

Safety Input 0

Safety Input 7
Status

Safety Input 6
Status

Safety Input 5
Status

Safety Input 4
Status

Safety Input 3
Status

Safety Input 2
Status

Safety Input 1
Status

Safety Input 0
Status

Safety Output
7 Status

Safety Output
6 Status

Safety Output
5 Status

Safety Output
4 Status

Safety Output
3 Status

Safety Output
2 Status

Safety Output
1 Status

Safety Output
0 Status

Reserved

Input Power
Error

(1)

Output Power
Error

(1)

Reserved

Muting Lamp 7
Status

Muting Lamp 3
Status

354 (852)

Safety and
standard

Safety Input 7

Safety Input 6

Safety Input 5

Safety Input 4

Safety Input 3

Safety Input 2

Safety Input 1

Safety Input 0

Safety Input 7
Status

Safety Input 6
Status

Safety Input 5
Status

Safety Input 4
Status

Safety Input 3
Status

Safety Input 2
Status

Safety Input 1
Status

Safety Input 0
Status

Safety Output
7 Status

Safety Output
6 Status

Safety Output
5 Status

Safety Output
4 Status

Safety Output
3 Status

Safety Output
2 Status

Safety Output
1 Status

Safety Output
0 Status

Safety Output
7 Monitor

Safety Output
6 Monitor

Safety Output
5 Monitor

Safety Output
4 Monitor

Safety Output
3 Monitor

Safety Output
2 Monitor

Safety Output
1 Monitor

Safety Output
0 Monitor

Reserved

Input Power
Error

(1)

Output Power
Error

(1)

Reserved

Muting Lamp 7
Status

Muting Lamp 3
Status

364 (868)

Safety and
standard

Safety Input 7
Status

Safety Input 6
Status

Safety Input 5
Status

Safety Input 4
Status

Safety Input 3
Status

Safety Input 2
Status

Safety Input 1
Status

Safety Input 0
Status

Safety Output
7 Status

Safety Output
6 Status

Safety Output
5 Status

Safety Output
4 Status

Safety Output
3 Status

Safety Output
2 Status

Safety Output
1 Status

Safety Output
0 Status

Test Output 7
Status

Test Output 6
Status

Test Output 5
Status

Test Output 4
Status

Test Output 3
Status

Test Output 2
Status

Test Output 1
Status

Test Output 0
Status

Reserved

Input Power
Error

(1)

Output Power
Error

(1)

Reserved

Muting Lamp 7
Status

Muting Lamp 3
Status

374 (884)

Safety and
standard

Safety Input 7

Safety Input 6

Safety Input 5

Safety Input 4

Safety Input 3

Safety Input 2

Safety Input 1

Safety Input 0

Safety Input 7
Status

Safety Input 6
Status

Safety Input 5
Status

Safety Input 4
Status

Safety Input 3
Status

Safety Input 2
Status

Safety Input 1
Status

Safety Input 0
Status

Safety Output
7 Status

Safety Output
6 Status

Safety Output
5 Status

Safety Output
4 Status

Safety Output
3 Status

Safety Output
2 Status

Safety Output
1 Status

Safety Output
0 Status

Safety Output
7 Monitor

Safety Output
6 Monitor

Safety Output
5 Monitor

Safety Output
4 Monitor

Safety Output
3 Monitor

Safety Output
2 Monitor

Safety Output
1 Monitor

Safety Output
0 Monitor

Test Output 7
Status

Test Output 6
Status

Test Output 5
Status

Test Output 4
Status

Test Output 3
Status

Test Output 2
Status

Test Output 1
Status

Test Output 0
Status

Reserved

Input Power
Error

(1)

Output Power
Error

(1)

Reserved

Muting Lamp 7
Status

Muting Lamp 3
Status

394 (916)

Only standard

Reserved

Output Power
Error

Input Power
Error

Test Output 7
Status

Test Output 6
Status

Test Output 5
Status

Test Output 4
Status

Test Output 3
Status

Test Output 2
Status

Test Output 1
Status

Test Output 0
Status

3A4 (932)

Only standard

Reserved

Output Power
Error

Input Power
Error

Safety Output
7 Monitor

Safety Output
6 Monitor

Safety Output
5 Monitor

Safety Output
4 Monitor

Safety Output
3 Monitor

Safety Output
2 Monitor

Safety Output
1 Monitor

Safety Output
0 Monitor

Test Output 7
Status

Test Output 6
Status

Test Output 5
Status

Test Output 4
Status

Test Output 3
Status

Test Output 2
Status

Test Output 1
Status

Test Output 0
Status

(1) This data is only diagnostic data. This data does not have safety integrity.

Table 50 - Input Data – 1791ES-IB8XOBV4 Modules (Continued)

Instance Hex
(decimal)

Connection Type

Byte

Bit 7

Bit 6

Bit 5

Bit 4

Bit 3

Bit 2

Bit 1

Bit 0

Summary of Contents for 1732ES-IB12XOB4

















































































































































































Search results

Summary of Contents for 1732ES-IB12XOB4

Reviews:

Allen-Bradley 1732ES-IB12XOB4, User Manual, Page: 141 / 176

Search results

Summary of Contents for 1732ES-IB12XOB4

Reviews: