AL-KO solo 127448, Original Instructions Manual

Page: 13 / 68

13
P
Remove Mounting bolts (a) and
open Cover (b).
Clean Element (c) if it is very dirty.
Return Element (c) to its original
position, and close Cover (b) with
Mounting bolts (a).
1.
2.
3.
Q
* Exchange oil after using the machine for 25 hours only for the first time
after purchase.
After that, exchange oil at 50-operating hour intervals according to the
degree of dirtiness.
** Maintenance techniques and special tools are necessary for this check
item. Therefore, consult our distributor near you.
The numbers in ( ) show the sections in this manual to be referred.
9.7.1 Checking the blade mounting bolts
9.1 Cleaning
9.2 Checklist
Wipe dirt off when this machine and the safety labels get dirty.
Do not directly spray water with a hose, etc. since it may cause a
machine failure.
Wipe with a dry rag after cleaning, and then wipe the metal surface
with a rag soaked with oil.
Clean the grass bag while spraying water with a hose. Use it after drying.
9.6 Ignition Plug
9.5 Air cleaner
9.3 Lubrication to Each Part
Regularly lubricate each bearing with an oilcan to keep the smooth operation
of each part.
9.4 Exchanging Engine Oil
NOTE
9. INSPECTION AND MAINTENANCE
See the engine instruction manual for the details of the maintenance of
the engine.
NOTE
Take sufficient caution not to get burnt since the engine and the
muffler are very hot right after the engine stops.
9.7 Blade
Incline this machine with the carburetor side of the engine positioned upside.
NOTE
Wear thick gloves when you check or attach or detach the blade.
Operating hours
Engine oil
Air cleaner
Loose bolt
Fuel
Ignition plug
Blade
Blade bolt
Grass bag
Throttle wire
Drive clutch wire
Blade wire
Gearshift wire
Valve clearance
Combustion chamber
Fuel tank
Strainer
Fuel tube
Check
Exchange
Cleaning
Check
Refueling
Cleaning
Adjust
Check
Check
Check
Cleaning
Adjust
Adjust
Adjust
Check
Adjust
Adjust
Cleaning
Cleaning
Cleaning
Check
Every
time
Time
25 50 100
EN
Plug Wrench
Oil pan
Drain
Bend New Blade
Flat
Chip
Wear
1.
2.
3.
1.
2.
3.
4.
5.
・
・
・
・
0.7 mm
○
○
○
○
○
○
○
○
○
★
○
○
○
○
○
○
○
○
★★
○ ★★
○ ★★
○
★★
○
Remove Plug cap (Q).
Remove Ignition plug (P) with the
attached plug wrench.
Exchange Ignition plug (P) if a great
amount of carbon is adhered to it or its
insulator is cracked or damaged.
Remove the carbon adhered to the
electrode, and adjust the electrode
clearance to 0.7 mm.
Install Ignition plug (P) and Plug cap (Q).
Remove the oil tank cap.
Drain the engine oil from the
drain port.
Fill with fresh engine oil after
drainage is complete.
Stop the engine and remove the ignition plug when you check the blade.
Extract gasoline first before tilting the engine to drain its oil.Treat and
dispose the drained engine oil properly according to the law in each country.
Fig. 28
Fig. 27
Fig. 32
Fig. 29
Fig. 30
Fig. 31
(See Fig. 27)
(See Fig. 28)
(See Fig. 29)
(See Fig. 30)
(See Fig. 31)
(8.1.1, 9.4)
(9.5)
(9.8)
(9.6)
(9.7)
(9.7.1)
(See Section 8.1.1)
WARNING
(8.1.3)
(8.1.4)
EN