background image

Form No. 3363-692 Rev A

48cm Super Bagger
48cm Recycler

®

Lawn Mower

Model No. 20835—Serial No. 310000001 and Up

Model No. 20836—Serial No. 310000001 and Up

Operator's Manual

Introduction

This rotary-blade, walk-behind lawn mower is
intended to be used by residential homeowners.
It is designed primarily for cutting grass on
well-maintained lawns on residential properties. It
is not designed for cutting brush or for agricultural
uses.

Read this information carefully to learn how to operate
and maintain your product properly and to avoid injury
and product damage. You are responsible for operating
the product properly and safely.

You may contact Toro directly at www.Toro.com for
product and accessory information, help finding a
dealer, or to register your product.

Whenever you need service, genuine Toro parts, or
additional information, contact an Authorized Service
Dealer or Toro Customer Service and have the model
and serial numbers of your product ready. Figure 1
identifies the location of the model and serial numbers
on the product. Write the numbers in the space
provided.

Figure 1

1.

Model and serial number plate

Model No.

Serial No.

This manual identifies potential hazards and has
safety messages identified by the safety alert symbol
(Figure 2), which signals a hazard that may cause serious
injury or death if you do not follow the recommended
precautions.

Figure 2

1.

Safety alert symbol

This manual uses two words to highlight information.

Important

calls attention to special mechanical

information and

Note

emphasizes general information

worthy of special attention.

This product complies with all relevant European
directives. For details, see the separate product specific
Declaration of Conformity (DOC) sheet.

For models with stated engine horsepower, the gross
horsepower of the engine was laboratory rated by the
engine manufacturer in accordance with SAE J1940.
As configured to meet safety, emission, and operating
requirements, the actual engine horsepower on this class
of lawn mower will be significantly lower.

Do not tamper with the engine controls or alter the
governor speed; doing so may create an unsafe condition
resulting in personal injury.

Safety

Improperly using or maintaining this mower can
result in injury. To reduce the potential for injury,
comply with these safety instructions.

Toro designed and tested this mower for reasonably safe
service; however, failure to comply with the following
instructions may result in personal injury.

To ensure maximum safety, best performance, and
to gain knowledge of the product, it is essential
that you and any other operator of the mower read

© 2009—The Toro® Company
8111 Lyndale Avenue South
Bloomington, MN 55420

Register at www.Toro.com.

Original Instructions (EN)

Printed in the USA

All Rights Reserved

Summary of Contents for 20835





















Reviews: