Agora Models Bismarck 08 Build Instructions Download

Page: 44 / 54

Fit one shaft

91-13

through the centre of the cog

91-06

and into the socket in the control post

91-04

Fit the second shaft into the hole in the aft control
post

91-04

Fit cog

91-07

on the second shaft

91-13

(on the right

in the orientation shown). The teeth on the base of
cog

91-07

interlock with the teeth on the rim of cog

91-06

. Cog

91-08

will be fitted next.

Fit cog

91-08

on the shaft

91-13

(not visible) on top of

cog

91-06

. The teeth on cog

91-08

interlock with the

teeth on the rim of cog

91-07

Fit the base plate

91-05

on the base of the aft control

post

91-04

. You will need two 2 x 5mm

screws.

Fix the base plate in place with two 2 x 5mm

screws.

Take the motor

89-01

and fit it into the base plate

91-05

so that the shaft of the motor engages in

the centre of cog

91-08

(the cog is not visible

from this angle).

91-07

91-08

91-04

91-13

91-06

91-13

91-08

91-06

91-07

2 x 5

91-05

91-04

91-05

89-01

91-13

AGORA

MODELS

AGORA

MODELS

Summary of Contents for Bismarck 08























































Search results

Summary of Contents for Bismarck 08

Reviews:

Related manuals for Bismarck 08

Brands by name

Popular brands

Agora Models Bismarck 08, Build Instructions

Search results

Summary of Contents for Bismarck 08

Reviews:

Related manuals for Bismarck 08

Brands by name

Popular brands