manualshive.com logo in svg

Agora Models Bismarck 08, Build Instructions

Share
Download
Agora Models Bismarck 08 Build Instructions Download Page 32

05

06

This shows the walkway in place on the wing. The 
wing can be swung back against the side of the 
bridge deck, as indicated by the arrow.  

Cut part 

G

 from frame 

87-06

. Bend it twice at right 

angles along the fold lines as shown. 

Cut railing 

H

 from frame 

87-06

. In the same way, 

bend it at right angles as shown. This railing is a 
mirror image of part 

G

.

Fit the peg on the base of the support arm, part 

E

, into 

the side of the bridge deck. Apply adhesive to the 
central slot in the arm, part 

F

. 

The starboard bridge wing is assembled in a similar 
way, using parts 

D

, 

E

 and 

F

 from frame 

87-05

. Start 

by fitting parts 

E

 and 

F

 together. 

Fix the walkway, part 

D

, in place, with the peg in the 

hole in the flange, so that it can swing backwards. Do 
not use any glue, as this part needs to move.

07

03

. FITTING THE RAILINGS

08

A

E

F

G

H

G

E

F

F

D

01

02

C

32

31

AGORA

MODELS

32

AGORA

MODELS

Summary of Contents for Bismarck 08























































Reviews:

No comments

Brands by name

Popular brands

Load more brands