manualshive.com logo in svg

Agora Models Bismarck 08, Build Instructions

Share
Download
Agora Models Bismarck 08 Build Instructions Download Page 9

03

. ADDING DETAILS TO THE HANGARS AND FIXING IN PLACE

05

Cut handrail 

M

 from frame 

82-08

. Bend the handrail 

at right angles along the two fold lines (arrows).

Bend the handrail 

M

 again at right angles at the next 

two fold lines, to make a U-shape as shown.

01

02

Cut handrail 

L

 from frame 

82-08

. Bend it twice at 

right angles to make a U-shaped rail that is a mirror 
image of handrail 

M

. 

Take the port hangar 

80-01

. Check the fit of handrail 

M

 on the roof. When you have it positioned correctly, 

apply a little superglue to the pegs and fix them into 
the recesses in the roof. 

06

Similarly, fix handrail 

L

 in place on the roof of the 

starboard hangar.

Cut ladder 

N

 from frame 

82-08

 and bend the two 

handrails upwards at right angles along the fold 
lines. Make sure you bend them in the correct 
direction, as shown.

80-01

M

M

M

M

L

L

80-02

N

03

04

9

9

AGORA

MODELS

10

AGORA

MODELS

Summary of Contents for Bismarck 08























































Reviews:

No comments

Brands by name

Popular brands

Load more brands