Agora Models Bismarck 08 Build Instructions Download

Page: 54 / 54

Completed work

The turbine room has been assembled and fitted
into the hull. You can now fit magnetised part

81-01

back in place. The guides from frame

92-10

will be

used in a future stage.

Take the armoured deck

92-18

and check the fit on

the longitudinal bulkhead, the angled bulkhead and
the three small supports, as shown. Glue in place.

Check the fit of the transverse bulkhead

92-15

on the

aft end of the turbine room assembly. Tabs at the top
and bottom of the turbine room assembly fit into slots
in the transverse bulkhead (circled). Glue in place.

Fit the transverse bulkhead

92-16

to the foward end

of the turbine room as shown. Again, it is held in place
by tabs located in slots. Glue in place.

Fit the back wall

92-17

onto the turbine room, locating

the tabs on the turbine room assembly into the slots
in part

92-17

(circled). Glue in place.

92-16

92-01

92-18

92-15

92-17

92-10

81-01

Remove the hull section

81-01

from the hull

assembly (held in place by magnets). Four raised
sockets on the base of the turbine room assembly
floor

92-01

(white arrows) fit onto corresponding pins

on the keel section. No glue is needed.

AGORA

MODELS

AGORA

MODELS

Summary of Contents for Bismarck 08























































Search results

Summary of Contents for Bismarck 08

Reviews:

Related manuals for Bismarck 08

Brands by name

Popular brands

Agora Models Bismarck 08, Build Instructions

Search results

Summary of Contents for Bismarck 08

Reviews:

Related manuals for Bismarck 08

Brands by name

Popular brands