manualshive.com logo in svg

Agora Models Bismarck 08, Build Instructions

Share
Download
Agora Models Bismarck 08 Build Instructions Download Page 46

Identify the back of the rotating dome 

91-02

 (arrow). 

Make sure that the peg on the end of arm 

B

 faces 

backwards (arrow). Apply a little glue to the end of the 
first part 

B

 and fix in place. Repeat to fit the second 

part 

B

, ensuring the peg is pointing backwards (arrow).

Cut the two target indicators 

C

 from frame 

91-01

. 

Check the fit on the roof of the control post 

91-04

, 

ensuring that they are facing the right way, as shown. 
Glue in place.

Check how the rotating dome 

91-02 

fits on the base 

91-03

. Apply a little glue to the rim of part 

91-02

. 

Fix the rotating dome 

91-02

 in place on the base 

91-03

 (not visible)

Cut the ladders 

F

 and 

G

 from frame 

91-11

. Bend the 

fixing tabs (four on part 

F

 and two on part 

G

) at right 

angles, as shown.

Cut the hand/foot rails structures 

E

 from frame 

91-11

. 

Check how they fit on the rangefinder arms. Glue in 
place as shown. 

05

06

03

. METAL DETAILS FOR THE ROTATING DOME AND CONTROL POST

F

C

E

B

D

91-04

91-02

C

91-04

91-02

91-02

91-04

G

E

91-03

91-03

07

08

01

02

46

46

AGORA

MODELS

47

AGORA

MODELS

Summary of Contents for Bismarck 08























































Reviews:

No comments

Brands by name

Popular brands

Load more brands