Agora Models Bismarck 08 Build Instructions Download Page 51

Page: 51 / 54

. SHAPING AND FITTING THE RAILINGS

This shows the five support brackets

in place on

part

92-02

, with the notched edges aligned (arrow).

Note the pegs on the support brackets (circled).

Check how the turbine assembly fits on the turbine
support

92-02

and brackets

so the pegs (circled

in previous step) are located in sockets in the turbine
assembly. When you are happy with the fit, apply
a little glue to the pegs and fix in place.

Glue the gangway

92-03

onto the turbine support

brackets as shown. Two pegs on the base of part

92-03

fit into corresponding holes in part

92-02

Take the small gangway

from frame

92-11

and glue

in place across the support brackets as shown.

Separate the railing

from the frame

92-19

. Bend

the railing three times at right angles at the notched
points as shown. See also step 5.

Take the railing

from frame

92-19

. Bend it once at

a right angle, as shown.

92-02

92-03

92-02

AGORA

MODELS

AGORA

MODELS

Summary of Contents for Bismarck 08























































Search results

Summary of Contents for Bismarck 08

Reviews:

Brands by name

Popular brands

Agora Models Bismarck 08, Build Instructions

Search results

Summary of Contents for Bismarck 08

Reviews:

Brands by name

Popular brands