manualshive.com logo in svg

Agora Models Bismarck 08, Build Instructions

Share
Download
Agora Models Bismarck 08 Build Instructions Download Page 41

03

Take the upper port hull section 

81-01

, supplied with 

stage 81. Place two magnets 

90-03

 on your worktop, 

with the letter S facing upwards. Apply a little 
superglue in the first recess (arrow).

Fix the second magnet holder 

A

 in place on the other 

side of the hull section with a 

PM

 screw.

Fix one of the magnets 

90-03

 into the first recess 

in part 

81-01

, positioning it so that the letter S 

(circled) is facing you. 

05

04

06

Fix a second magnet 

90-03

 into the second recess at 

the top of part 

81-01

, using superglue, as before. 

Ensure that the letter S is facing you.

Check the difference between the magnet holders 

A

 

and 

B

 on frame 

90-02

. The holders 

A

 are slightly 

smaller than 

B

. For the two magnets that have been 

fitted, you will need two 

A

 holders and two 

PM

 

screws. Fit one of the brackets in place, as indicated. 

Fix the first magnet holder 

A

 to the hull section 

81-01

 

with a 

PM

 screw. The holder covers the end of the first 

magnet 

90-03

.

02

. FITTING THE MAGNETS

01

02

A

A

90-03

81-01

81-01

90-03

81-01

A

PM

PM

A

90-03

90-03

PM

81-01

81-01

41

41

AGORA

MODELS

42

AGORA

MODELS

Summary of Contents for Bismarck 08























































Reviews:

No comments

Brands by name

Popular brands

Load more brands