manualshive.com logo in svg

Agora Models Bismarck 08, Build Instructions

Share
Download
Agora Models Bismarck 08 Build Instructions Download Page 7

03

04

05

06

Check the fit of the vent 

B

 on the side of the barbette 

19-02

 and glue in place as shown.

Cut the vent 

F

 from the frame 

82-01

. Check the fit 

to the starboard side of the barbette and glue in 
place as shown.

Cut vent 

D

 from frame 

82-01

. Check the fit on the 

side of the barbette and glue in place as shown, near 
vent 

F.

 

Finally, cut the vent 

C

 from the frame and check the 

fit near the vent 

D

, slipping it behind the small rope 

reel 

76-02

. Glue in place as shown.

Cut a joint from frame 

82-05

 and smooth the 

underside with sandpaper. You will also need a 
lever 

82-06

.

Push the end of the lever 

82-06

 into the joint 

82-05

 

as shown. The lever clicks into place – do not use any 
glue.

01

02

02

. TWO BREAKWATERS AND A LADDER

F

F

C

D

E

19-02

19-02

D

19-02

19-02

B

76-02

82-05

82-06

82-05

82-06

7

7

AGORA

MODELS

8

AGORA

MODELS

Summary of Contents for Bismarck 08























































Reviews:

No comments

Brands by name

Popular brands

Load more brands