Agora Models Bismarck 08 Build Instructions Download

Page: 47 / 54

The ladders with rails

91-09

fit across the back of

the rotating dome

91-02

. Pegs on the ladders fit

into corresponding holes in the rotating dome.
Glue in place.

Completed work

The aft fire control post has been assembled, with
many detailed features. The motor has been attached
to the base of the fire control post.

Ladder

fits on the back of the control post

91-04

Glue in place.

The radar antenna

91-12

has two pegs that fit into the

two central holes on the back of the rotating dome

91-02

. Make sure you have it the right way up, as

shown. Glue in place.

The cooling coil

91-10

fits on the front of the rotating

dome

91-02

: pegs on each end fit into holes in the

rotating dome. Glue in place.

Check how ladder

fits on the front of the aft mast.

Glue in place.

91-12

91-04

91-10

91-09

91-02

AGORA

MODELS

AGORA

MODELS

Summary of Contents for Bismarck 08























































Search results

Summary of Contents for Bismarck 08

Reviews:

Related manuals for Bismarck 08

Brands by name

Popular brands

Agora Models Bismarck 08, Build Instructions

Search results

Summary of Contents for Bismarck 08

Reviews:

Related manuals for Bismarck 08

Brands by name

Popular brands