Agora Models Bismarck 08 Build Instructions Download Page 17

Page: 17 / 54

Supporting the deck from behind, fix the motor

55-01

in place with the two

PWB

screws that were removed.

There is a second cable slot to the other side of the
deck section

22-01

. Thread the cables labelled

B-14

B-15

B-18

B-19

B-20

B-21

and

B-22

through the

slot, as shown (red arrow).

Identify the bracket with slots on the underside of
deck section

48-01

(arrow). Fit the cable labelled

B-19

into the first slot as shown.

Thread the cables labelled

B-21

and

B-22

through the

same slot, in the same direction.

. FITTING THE CABLES

Thread the cable from the motor

55-01

(labelled

B-20

)

through the slot at the edge of the deck

19-01

(arrow).

Identify the cable slot at the edge of deck section

22-01

(white arrow). Thread the cables labelled

B-3

B-4

B-5

B-6

B-7

B-8

and

B-9

through the slot.

55-01

B-19

19-01

55-01

B-20

19-01

B-22

B-21

19-01

22-01

B-3, B-4, B-5 B-6,

B-7, B-8, B-9

B-14, B-15, B-18 B-19,

B-20, B-21, B-22

22-01

48-01

PWB

AGORA

MODELS

AGORA

MODELS

Summary of Contents for Bismarck 08























































Search results

Summary of Contents for Bismarck 08

Reviews:

Brands by name

Popular brands

Agora Models Bismarck 08, Build Instructions

Search results

Summary of Contents for Bismarck 08

Reviews:

Brands by name

Popular brands