Agora Models Bismarck 08 Build Instructions Download

Page: 53 / 54

Glue the angled brackets

to the torpedo bulkhead

92-13

and longitudinal bulkhead

as shown.

Identify four tabs on the longitudinal bulkhead

92-14

(circled). Check how they fit into the slots on the
bulkhead

92-13

When you are happy with the fit, glue the bulkhead

92-13

in place. It sits at a slight angle, as shown.

Check the fit of the angled bulkhead

92-12

on the

bulkhead assembly: a rib on part

92-12

fits beneath the

edge of the bulkhead

92-13

(arrow). Apply a little glue

to the edge of the bulkhead

92-13

and the lower edge

of bulkhead

92-12

and fix in place, as shown.

The three small supports

from the frame

92-11

are

glued into the three openings of the angled bulkhead

92-12

. The angled end of the supports fit into part

92-12

so they appear vertical, as seen in the next step.

Check the fit of the bulkhead assembly from step 7 on
the curved part of the floor

92-01

. Pegs on the edges of

the longitudinal bulkhead

92-14

and torpedo bulkhead

92-13

fit into recesses of the floor panel

92-01

. When

you are happy with the fit, glue in place.

92-14

92-01

92-13

92-14

92-12

92-14

92-13

AGORA

MODELS

AGORA

MODELS

Summary of Contents for Bismarck 08























































Search results

Summary of Contents for Bismarck 08

Reviews:

Related manuals for Bismarck 08

Brands by name

Popular brands

Agora Models Bismarck 08, Build Instructions

Search results

Summary of Contents for Bismarck 08

Reviews:

Related manuals for Bismarck 08

Brands by name

Popular brands