manualshive.com logo in svg

Agilent Technologies n5181a, Service Manual, Page: 197 / 202

Share
Download
Agilent Technologies n5181a Service Manual Download Page 197

Agilent N5161A/62A/81A/82A/83A MXG Signal Generators Service Guide

  

5-

 1

5

Safety and Regulatory

This chapter provides information on the following:

•

“General Safety Considerations” on page 5-1

•

“Lithium Battery Disposal” on page 5-2

•

“Assistance” on page 5-2

•

“Certification” on page 5-2

The following safety notes are used throughout this manual. Familiarize yourself with each of the notes and its meaning before operating this 
instrument.

WARNING

Warning denotes a hazard. It calls attention to a condition or situation that could result in personal injury or loss of 
life. Do not proceed beyond a warning until you fully understand the indicated conditions or situations.

CAUTION

Caution calls attention to a condition or situation that could result in damage to or destruction of the signal generator, or in the 
loss of a user’s settings or data. Do not proceed beyond a caution until you fully understand the indicated conditions.. 

General Safety Considerations

The following safety notes apply specifically to signal generators. These notes also appear in other chapters of this service guide as required. 

WARNING

These servicing instructions are for use by qualified personal only. To avoid electrical shock, do not perform any 
servicing unless you are qualified to do so.

WARNING

The opening of covers or removal of parts is likely to expose dangerous voltages. Disconnect the product from all 
voltage sources before starting to open.

WARNING

The detachable power cord is the instrument disconnecting device. It disconnects the main circuits from the main 
supply before other parts of the instrument. The front panel switch is only a standby switch and is not a LINE switch 
(disconnecting device).

WARNING

The power cord is connected to internal capacitors that may remain live for 5 seconds after disconnecting the plug 
from its power supply.

WARNING

This is a Safety Class 1 Product (provided with a protective earthing ground incorporated in the power cord). The 
mains plug shall only be inserted in a socket outlet provided with a protective earth contact. Any interruption of the 
protective conductor inside or outside of the product is likely to make the product dangerous. Intentional interruption 
is prohibited.

WARNING

Replace battery only with the same or equivalent type recommended. Discard used batteries according to 
manufacturer’s instructions.

WARNING

If this product is not used as specified, the protection provided by the equipment could be impaired. This product 
must be used in a normal condition (in which all means for protection are intact) only.

CAUTION

Many of the assemblies in this instrument are very susceptible to damage from electrostatic discharge (ESD). Perform service 
procedures only at a static-safe workstation and wear a grounding strap.

深圳德标仪器 

135-1095-0799

Summary of Contents for n5181a











































































































































































































Reviews:

No comments