manualshive.com logo in svg

Agilent Technologies n5181a, Service Manual, Page: 193 / 202

Share
Download
Agilent Technologies n5181a Service Manual Download Page 193

 

Agilent Technologies N5161A/62A/81A/82A/83A MXG Signal Generators Service Guide

Post-Repair Procedures and Performance Verification 

Leveled Output Power Verification (N5161A/62A

1

/81A/82A Only) 

4-13

Leveled Output Power Verification (N5161A

1

/62A

1

/81A/82A Only)

This test verifies that the output power from the signal generator is within defined limits. The following table lists the preferred equipment 
for this test. 

•

“N5161A

1

/81A Output Power Test Procedure” on page 4-13

•

“N5162A/82A Output Power Test Procedure” on page 4-15

N5161A

1

/81A Output Power Test Procedure

1.

Zero and calibrate the power sensor to the power meter:

2.

Connect the equipment as shown:

3.

Preset the signal generator: Press 

Preset

.

4.

Turn RF on: Press 

RF On/Off

 so that the RF On/Off LED lights.

5.

Turn modulation off: Press 

Mod On/Off

 so that the Mod On/Off LED turns off.

6.

Set the frequency: Press 

Frequency

 and enter the first frequency value listed in 

Table 4-10

.

1

The N5161A/62A performs the identical internal tests as in the MXG via a LAN connection to a Web Server.  The front panel displays all hardkeys, softkeys and test results 

as depicted in the illustration. For information on Web-Enabled Control refer to

 

“Accessing the MXG Web-Enabled Page” on page 1-18

 

and to the

 

Programming 

Guide.

 

Test Equipment

Recommended Model

Power Meter

Agilent E4418B or E4419A/B E-Series power meter

Power Sensor,

 

Input: Type-N (m)

Agilent E9304A

Table 4-10Leveled Output Power Limits 

Frequency

Limits (dB)

125 MHz

< 0.6dB

275 MHz

< 0.6dB

338 MHz

< 0.6dB

425 MHz

< 0.6dB

深圳德标仪器 

135-1095-0799

Summary of Contents for n5181a











































































































































































































Reviews:

No comments