manualshive.com logo in svg

Agilent Technologies n5181a, Service Manual, Page: 130 / 202

Share
Download
Agilent Technologies n5181a Service Manual Download Page 130

Agilent N5161A/62A/81A/82A/83A MXG Signal Generators Service Guide

 

 

Assembly Replacement
A9 Interface Board (N5161A/62A only)

3-18

A9 Interface Board (N5161A/62A only)

Tools Required 

•

T-10 driver 

Removal Procedure

Refer to 

Figure 3-8

 for this procedure. 

1.

Disconnect the power cord.

2.

Remove the covers from the signal generator. Refer to 

”Outer Cover” on page 3-4

, 

”Inner Top Cover” on page 3-6

, and 

”Inner Bottom 

Cover” on page 3-8

.

3.

Remove the front-panel from the signal generator. Refer to 

”Front-Panel” on page 3-10

.

4.

Disconnect the W1 ribbon cable from the A9 Interface board (3).

5.

Using the T-10 driver, remove the six screws (1) that secure the subpanel (2) to the front panel (3).

6.

Disconnect the Power Switch cable (4) from the A9 Interface Board (3).

7.

Using the T-10 driver, remove the seven screws (5) that secure the A9 Interface Board (3) to the front-panel sub-panel (6).

8.

Remove the A9 Interface Board.

Replacement Procedure 

1.

Reverse the order of the removal procedure.

2.

Torque all screws to 9 in–lbs.

3.

Perform the post-repair performance tests that pertain to this replacement procedure, see 

Chapter 4, Post-Repair Procedures and 

Performance Verification

.

深圳德标仪器 

135-1095-0799

Summary of Contents for n5181a











































































































































































































Reviews:

No comments