manualshive.com logo in svg

Agilent Technologies n5181a, Service Manual, Page: 164 / 202

Share
Download
Agilent Technologies n5181a Service Manual Download Page 164

Agilent N5161A/62A/81A/82A/83A MXG Signal Generators Service Guide

 

 

Assembly Replacement
A4 Internal Memory Card (N5162A/82A only)

3-52

A4 Internal Memory Card (N5162A/82A only)

Tools Required 

•

T-10 driver

Removal Procedure 

Refer to 

Figure 3-29

 for this procedure.

1.

Disconnect the power cord.

2.

Remove the covers from the signal generator. Refer to 

”Outer Cover” on page 3-4

 and 

”Inner Bottom Cover” on page 3-8

.

3.

Place the signal generator flat and upside down with the rear panel facing you.

4.

Using the T-10 driver, remove the screw (1) that attaches the A4 Internal Memory Card to the A3 RF assembly.

5.

Remove the A4 Internal Memory Card by gently rocking it side to side to release the pin.

Replacement Procedure 

1.

Reverse the order of the removal procedure.

CAUTION

The A4 Internal Memory Card pin can be re-installed incorrectly. To insure proper installation carefully align the connector 

on the A4 Internal Memory Card with the connector on the A3 RF assembly.

2.

Torque all screws to 9 in–lbs.

3.

Perform the post-repair performance tests that pertain to this replacement procedure, see 

Chapter 4, Post-Repair Procedures and 

Performance Verification

.

深圳德标仪器 

135-1095-0799

Summary of Contents for n5181a











































































































































































































Reviews:

No comments