manualshive.com logo in svg

Agilent Technologies n5181a, Service Manual, Page: 133 / 202

Share
Download
Agilent Technologies n5181a Service Manual Download Page 133

 

Agilent N5161A/62A/81A/82A/83A MXG Signal Generators Service Guide

Assembly Replacement 

Power Switch 

3-21

Power Switch

Tools Required 

•

T-10 driver 

Removal Procedure

Refer to 

Figure 3-10

 for this procedure. 

1.

Disconnect the power cord.

2.

Remove the covers from the signal generator. Refer to 

”Outer Cover” on page 3-4

, 

”Inner Top Cover” on page 3-6

, and 

”Inner Bottom 

Cover” on page 3-8

.

3.

Remove the front-panel from the signal generator. Refer to 

”Front-Panel” on page 3-10

.

4.

Remove the A6 DC-AC Inverter Interface Board from the signal generator. Refer to 

”A6 DC-AC Inverter Interface Board 

(N5181A/82A/83A only)” on page 3-16

.

5.

Remove the LCD Display from the signal generator. Refer to 

”LCD Display (N5181A/82A/83A only)” on page 3-14

.

6.

Using the T-10 driver, remove the two screws (1) that secure the Power Switch (2) to the front-panel frame.

7.

Remove the Power Switch.

Replacement Procedure 

1.

Reverse the order of the removal procedure.

2.

Torque all screws to 9 in–lbs.

3.

Perform the post-repair performance tests that pertain to this replacement procedure, see 

Chapter 4, Post-Repair Procedures and 

Performance Verification

.

Figure 3-10Power Switch

1

2

screws not shown

Note: N5161A/62A use the longer power switch cable

深圳德标仪器 

135-1095-0799

Summary of Contents for n5181a











































































































































































































Reviews:

No comments