manualshive.com logo in svg

Agilent Technologies n5181a, Service Manual, Page: 86 / 202

Share
Download
Agilent Technologies n5181a Service Manual Download Page 86

Agilent N5161A/62A/81A/82A/83A MXG Signal Generators Service Guide

 

Replaceable Parts 
Assemblies and Hardware Options 

2-4

Table 2-2 N5181A/82A

Description

Option 501

Option 503

Option 506

Part Number

Page Number

Part Number

Page Number

Part Number

Page Number

Front Panel - N5181A (Analog) 

N5180-60110

2-10

N5180-60110

2-10

N5180-60110

2-10

Front Panel - N5182A (Vector)

n/a

n/a

N5180-60111

2-10

N5180-60111

2-10

Key Pad

N5180-60021

2-8

N5180-60021

2-8

N5180-60021

2-8

Power Switch

N5180-60022

2-8

N5180-60022

2-8

N5180-60022

2-8

USB Board

N5180-60023

2-8

N5180-60023

2-8

N5180-60023

2-8

LCD

N5180-60024

2-8

N5180-60024

2-8

N5180-60024

2-8

A1 Power Supply

N5180-60060

2-10

N5180-60060

2-10

N5180-60060

2-10

A2 Vector Module Assembly 
(N5182A only)

n/a

n/a

N5180-69006

2-10

N5180-69006

2-10

A3 RF Assembly

See 

Table 2-3

 or 

Table 2-4

 for serial number specific assemblies.

A3BT1 Lithium Battery

1420-0356

2-13

1420-0356

2-13

1420-0356

2-13

A4 Internal Memory Card (N5182A 
only)

n/a

n/a

1819-0693

2-13

1819-0693 

2-13

A5 CPU

a

a

The replacement of the A5 CPU requires firmware 

≥

A.01.60.

N5180-60190

2-13

N5180-60190

2-13

N5180-60190

2-13

A6 DC-AC Inverter Interface

N5180-60025

2-8

N5180-60025

2-8

N5180-60025

2-8

B1 thru B4 Fan (each)

b

b

There are two different fans structured to this part number. The fan currently shipping has a thickness of 20mm. The fan that shipped previously had a thickness of 25mm. Both fans 

are acceptable to use.

N5180-60026

2-10

N5180-60026

2-10

N5180-60026

2-10

CVR, Front Panel

N5180-40012

2-29

N5180-40012

2-29

N5180-40012

2-29

Table 2-3 N5181A/82A Instrument Serial Number < xx4818xxxx

Description

Option 501

Option 503

Option 506

Part Number

Page Number

Part Number

Page Number

Part Number

Page Number

A3 RF Assembly UNM

ab

 

 

(front panel output)

a

The replacement of the A3 RF assembly requires firmware 

≥

A.01.42. To avoid configuration errors, download firmware 

≥

A.01.42 prior to replacing the A3 assembly. If the A3 RF 

assembly is replaced prior to downloading firmware 

≥

A.01.42, downloading firmware 

≥

A.01.42 and cycling the power should correct any configuration errors.

N5180-69122

2-13

N5180-69122

2-13

N5180-69124

2-13

A3 RF Assembly UNM with 1EL, or 
UNU, or UNT (front panel output)

N5180-69122

2-13

N5180-69122

2-13

N5180-69124

2-13

A3 RF Assembly UNM with

 

1EL, or UNU, or UNW, or UNT, or 
all & any combination or all of the 
following options; UNV, UNZ, 1EA, 

1EQ and 099

a

 

(front panel output)

N5180-69123

2-13

N5180-69123

2-13

N5180-69125

2-13

A3 RF Assembly 1EM All (

Any 

combination of options or no

 

options

)

a

 (rear panel output)

N5180-69170

2-13

N5180-69170

2-13

N5180-69170

2-13

深圳德标仪器 

135-1095-0799

Summary of Contents for n5181a











































































































































































































Reviews:

No comments