Agilent Technologies n5181a Service Manual Download Page 200

Page: 200 / 202

Agilent N5161A/62A/81A/82A/83A MXG Signal Generators Service Guide

Instrument History

6-2

•

Firmware release A.01.20

•

43x Options introduced.

•

Five Pack licensing available.

•

Release of upgradeable internal BBG maximum sample rate.

•

Softkeys for “Int Phase Polarity” and “Burst Envelope” added.

•

A3 RF Assembly part number N5180-60076

December 2006 (N5181A/82A only)

•

Firmware release A.01.10

•

Compatibility languages for Agilent, Aeroflex, IFR, and Rhonde&Schwartz signal generators released.

•

Option and license file backup locations on the A3 RF Assembly and the A5 CPU implemented.

•

A3 RF Assembly part number N5180-60065

September 2006 (N5181A/82A only)

Initial release of the N5181A/82A MXG Signal Generators.

•

Serial prefix US/MY/SG4624

•

Firmware release A.01.04

•

A3 RF Assembly part number N5180-60001

深圳德标仪器

135-1095-0799

Summary of Contents for n5181a











































































































































































































Search results

Summary of Contents for n5181a

Reviews:

Agilent Technologies n5181a, Service Manual, Page: 200 / 202

Search results

Summary of Contents for n5181a

Reviews: