manualshive.com logo in svg

Agilent Technologies n5181a, Service Manual, Page: 138 / 202

Share
Download
Agilent Technologies n5181a Service Manual Download Page 138

Agilent N5161A/62A/81A/82A/83A MXG Signal Generators Service Guide

 

 

Assembly Replacement
Rear Panel (N5183A)

3-26

Rear Panel (N5183A)

Tools Required 

•

T-10 driver 

•

5/8” hex-nut driver

Removal Procedure

Refer to 

Figure 3-13

 for this procedure.

1.

Disconnect the power cord.

2.

Remove the covers from the signal generator. Refer to 

”Outer Cover” on page 3-4

, 

”Inner Top Cover” on page 3-6

, and 

”Inner Bottom 

Cover” on page 3-8

.

3.

Place the signal generator flat with the rear panel facing you.

4.

Disconnect W15 from A7J14.

5.

Using the 5/8” hex-nut driver, remove the nine nuts and washers (1) securing the A3 RF assembly and A7 Micro Deck BNC’s to the rear 
panel.

6.

Using the T-10 driver, remove the nine screws (2) securing the rear panel to the signal generators chassis.

7.

Pull the rear panel away from the signal generator’s chassis.

Replacement Procedure 

1.

Reverse the order of the removal procedure.

2.

Torque all screws to 9 in–lbs.

3.

Torque all BNC connectors to 8 in–lbs.

4.

Perform the post-repair performance tests that pertain to this replacement procedure, see 

Chapter 4, Post-Repair Procedures and 

Performance Verification

.

深圳德标仪器 

135-1095-0799

Summary of Contents for n5181a











































































































































































































Reviews:

No comments