Home
/
Agilent Technologies
/
n5181a
/
Service Manual

Agilent Technologies n5181a, Service Manual, Page: 198 / 202

Share

183 pages before
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202

Page: 198 / 202

Agilent Technologies n5181a Service Manual Download Page 198

Agilent N5161A/62A/81A/82A/83A MXG Signal Generators Service Guide

Safety and Regulatory
Lithium Battery Disposal

5-2

Lithium Battery Disposal

When the battery on the A14 CPU is exhausted and/or ready for disposal, dispose of it according to your country’s requirements. You can
return the battery to your nearest Agilent Technologies Sales and Service office for disposal, if required.

Figure 5-1

Assistance

Product maintenance agreements and other customer assistance agreements are available for Agilent Technologies products. For any
assistance, contact your nearest Agilent Technologies sales and service office.

Certification

Agilent Technologies Company certifies that this product met its published specifications at the time of shipment from the factory. Agilent
Technologies further certifies that its calibration measurements are traceable to the United States National Institute of Standards and
Technology, to the extent allowed by the Institute’s calibration facility, and to the calibration facilities of other International Standards
Organization members.

深圳德标仪器

135-1095-0799

«
...
196
197
198
199
200
...
»

Summary of Contents for n5181a











































































































































































































Reviews:

No comments