Agilent Technologies G3437A Installation Instructions Manual Download Page 16 | Manualshive

Page: 16 / 20

background image

16

Installation Instructions

Agilent G3437A Side-Mounted Thermal Conductivity Detector

Attach the TCD board

1

Remove the TCD logic board from its static control bag.

2

Align the TCD board with the frame (3rd TCD) so the board circuits are
facing up and the board notches are to the left of the frame hooks.

3

Slide the TCD board under the hooks so that all the slots engage all the
hooks and the board lies flat and evenly on the frame. Align the thumb
screw directly over the screw hole.

4

Attach the TCD board to the frame by tightening the thumb screw.

Figure 21

TCD board attached to frame (3rd TCD)

Attach the PCB cover

1

Insert the PCB cover tabs into the frame (3rd TCD) slots and tilt the cover
into position over the board.

2

Fasten the cover with a Torx screw.

Thumbscrew

Frame hooks

Frame hooks

«
...
14
15
16
17
18
...
»

Summary of Contents for G3437A





















Reviews:

No comments

Related manuals for G3437A

Luxomat PD2-DIM Series

Brand: B.E.G. Pages: 2

LUXOMAT PD4-M-1C-C-PS

Brand: B.E.G. Pages: 4

Pack TYXAL+ Access

Brand: DELTA DORE Pages: 11

Brand: Tasco Pages: 24

Brand: Veilux Pages: 37

Brand: LST Pages: 1

Enforcer SM-407-5T

Brand: SECO-LARM Pages: 1

CasinoCam DDF3000AV

Brand: dallmeier Pages: 33

Brand: Abus Pages: 18

Brand: Arm Electronics Pages: 1

Brand: delight Pages: 2

Brand: ZIGBEE Pages: 73

Brand: Vestil Pages: 5

Brand: Avue Pages: 11

Brand: Avue Pages: 15

Brand: 8level Pages: 4

Brand: Axis Pages: 62

Brand: Axis Pages: 60

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands