8-19
Instrument BASIC
Entering and Editing Programs
Line-by-line Entry and Editing
Program lines in the Agilent 8922M/S’s RAM can be entered and edited one line at
a time from your computer using the PROG command -
OUTPUT Addr;”PROG:EXEC ‘<program line/command> ’”
with <program/command> representing any command or program line you want to
enter.
For example, to enter or change line 20 of a program to ‘20 A=3.14’, you would
enter the following command on your computer
OUTPUT Addr;”PROG:EXEC ‘20 A=3.14 ’”
Quoted strings, such as those used in PRINT commands, must use double quotes.
Example -
OUTPUT Addr;”PROG:EXEC ‘30 PRINT “”TEST”” ’”
Using a Terminal
A connected terminal, or PC using a terminal emulator, is used to enter characters
directly into the Agilent 8922M/S IBASIC Controller’s command line.
Editing a program line requires you to re-enter the full line with corrections.
Configuring your terminal/PC for this operation is explained in this chapter, ‘Serial
Port Configuration for Programming” on page 8-6.
Entering Commands
When program lines or commands are entered, you press the ENTER key on your
terminal to execute the command. For example, to LIST a program in RAM you
would type LIST,
This differs from using the Cursor Control knob to enter characters where you select
‘Done’ to execute the command.
ENTER
Summary of Contents for 8922M
