Agilent Technologies 8922M, User Manual

Page: 376 / 381

Index
Index-6
Output RF Spectrum (Trace View), 4-
85
Phase/Freq (Phase Err), 4-91
Pwr Ramp (Fall Edge), 4-100
Pwr Ramp (Rise Edge), 4-95
Pwr Ramp (Top 2 dB), 4-97
marker position, 4-97, 4-100
pulse fall, 4-110
pulse on/off ratio, 4-107
Marker To Peak+
Oscilloscope (Marker Controls), 4-81
Marker To, Ref Level
Spectrum Analyzer (Marker Controls),
4-126
Markerl
Oscilloscope (Trigger Controls), 4-78
MarkerPos
Pulse Fall, 4-110
Pulse Rise, 4-107
Mask
Pwr Ramp (Fall Edge), 4-100
Pwr Ramp (Rise Edge), 4-96
Pwr Ramp (Top 2 dB), 4-98
Max Hold
Spectrum Analyzer (Main Controls), 4-
123
MCC
Cell Config, 4-20, 4-26
Meas Cntl
Bit Error Test, 4-14
Meas Num
Bit Error Test, 4-12
Meas Reset
Audio, 4-6
Configure, 4-51
CW Meas, 4-55
Oscilloscope (Main Controls), 4-76
Oscilloscope (Marker Controls), 4-81
Oscilloscope (Trigger Controls), 4-78
Spectrum Analyzer (MainControls), 4-
123
Measurement
Bit Error Test, 4-13
measurement arming
keys, 5-5
measurement averaging, 5-3
measurement control, 4-10, 4-14
Measurement Summary
Pwr Ramp (Summary), 4-102
measurement summary message, 2-17
measurement synchronization, 4-64
measurement synchronization screen
keys, 5-6
memory cards
backing up programs, 8-23
batteries, 8-24
COPY_PL program, 8-23
initializing, 8-21
inserting and removing, 8-20
SRAM and OPT part numbers, 8-21
write-protect switch, 8-22
message screen
keys, 5-6
messages, 7-1
bad sync, 7-4
Communication Failures, 7-2
Firmware Errors, 7-3
FM error, 7-4
level late, 7-4
level short, 7-4
low level, 7-4
measurement summary, 2-17
no error, 7-4
protocol errors, 7-5
RF overload, 7-4
short burst, 7-4
sync status, 7-4
meter
keys, 5-6
Midamble
Measurement Sync, 4-66
Midamble Start Bit Position
Measurement Sync, 4-67
MM
Cell Control, 4-41
MNC
Cell Config, 4-20, 4-26
mobile
country code, 4-20, 4-26
network code, 4-20, 4-26
mobile allocation
number, 4-40
number 1, 4-19, 4-25
number 2, 4-20, 4-25
mobile allocation index
offset 1, 4-20, 4-26
offset 2, 4-20, 4-26
mobile station
information, 4-70
timing error, 4-43
mobile station information screen
keys, 5-6
mobility management, 4-41
Mode
Cell Control, 4-41
Configure, 4-60
Output RF Spectrum (Main View), 4-
83
Mode field, 8-5
model
I/O configuration, 4-60
modulation
output RF spectrum power, 4-83
multi-burst measurements, 2-15
N
NCC
Cell Configuration, 4-20, 4-26
NetwkOnly, A-12
Next Peak (Marker To)
Spectrum Analyzer (Marker Controls),
4-125
no
keys, 5-6
no error message, 7-4
Norm
Cell Control, 4-41
O
Off, 4-10, 4-14
Offset
Configure, 4-51
On UUT Failure
continue or stop, 8-29
On/Off
Phase/Freq (Multi-burst), 4-89
on/off
keys, 5-6
One-Time Programmable