manualshive.com logo in svg

AGI 1549, Assembly Manual

Share
Download
AGI 1549 Assembly Manual Download Page 71

8210-10003 R0

71

3.21. Align the Conveyor Belt

Basic Conveyor Belt Alignment:

The conveyor belt will run straight when all of the rollers are straight.

Loosen or tighten the adjustment bolt(s) to align the conveyor belt. Tighten the side the belt has moved toward,
or loosen the side the belt has moved away from.

Belt alignment is done while the belt is running.

Figure 1.

Roller out of Alignment

OR

LOOSEN

TIGHTEN

Before Aligning the Belt:

• The conveyor must be empty of all grain.

• The belt doesn't ride up over top of the interior trough guide blocks.

• Wait until the belt makes a complete revolution before adjusting the rollers. Some belts may have uneven

edges, appearing misaligned.

To Align the Belt:

If your belt is tracking off-center, follow the sections and steps in the order following to center it.

Figure 2.

Belt Tracking to One Side

After aligning and tracking the belt, adjust the position of the interior trough guide blocks and install the
remaining U-trough covers.

UCX3 S-DRIVE FIELD LOADER – PORTABLE GRAIN BELT CONVEYOR

3. ASSEMBLY

Summary of Contents for 1549



























































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands