manualshive.com logo in svg

AGI 1549, Assembly Manual

Share
Download
AGI 1549 Assembly Manual Download Page 108

108

8210-10003 R0

Fuel Filter

From Primer Bulb

To Gas Engine 

Fuel Filter

Clamp

Æ

3. If equipped with an low emission tank kit, install a fuel demand valve. Cut the fuel line between the primer

bulb and the fuel filter. Insert the fuel demand valve into the fuel line with hose clamps.

Fuel Demand Valve

To Fuel Filter

From Primer Bulb 

Hose Clamp

Fuel Demand Valve

Hose Clamp

Fuel Demand Valve

4. Connect the fuel line to the engine using hose clamp.

5. Secure the fuel hoses with zip ties.

After installation check

Note

Before checking the primer bulb, please proceed and complete all the assemblies first and after the
conveyor is completely assembled, place finishing zip-ties on all fuel hoses to ensure all lines are snug in
place. Also zip-tie the gearbox breather to the fuel hose above the fuel filter.

1. Prime the fuel system with the primer bulb until fuel is seen in the fuel filter.

2. Run the machine and check all connections for any leaks or loose fitting.

Important

Do not start the engine on empty fuel, before pumping the primer bulb. Otherwise you risk wearing
out the battery, and may risk of engine failure.

3. ASSEMBLY

UCX3 S-DRIVE FIELD LOADER – PORTABLE GRAIN BELT CONVEYOR

Summary of Contents for 1549



























































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands