manualshive.com logo in svg

AGI 1549, Assembly Manual

Share
Download
AGI 1549 Assembly Manual Download Page 104

104

8210-10003 R0

3.36. Align the Winch

This procedure describes the alignment of the winch.

1. Check the alignment of the winch by watching the cable wrapping on the drum as the conveyor is raised.

Proper alignment is achieved when the cable indexes, filling each row on the drum evenly and not piling up
against one side.

2. Lower the conveyor fully if the cable does not index properly until there is slack in the cable.

3. Loosen the bolts holding the winch, adjust the winch, re-tighten bolts and retest.

3.37. Install the Tank Kit and the Primer Bulb

Depending on the region two different versions of tank kit are provided with the conveyors. The size and shape
of the fuel tank can vary depending on the conveyor series. Examples of gas tank are shown below:

Gas Tank Type

Low Emission Gas Tank (US only)

Gas Tank (Outside US)

Fuel Hose Connecting Port

Spout Side

Hopper Side

Fuel Hose Connecting Port

Spout Side

Hopper Side

3. ASSEMBLY

UCX3 S-DRIVE FIELD LOADER – PORTABLE GRAIN BELT CONVEYOR

Summary of Contents for 1549



























































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands