manualshive.com logo in svg

AGI 1549, Assembly Manual

Share
Download
AGI 1549 Assembly Manual Download Page 15

8210-10003 R0

15

WARNING

To prevent serious injury or 

equipment damage, lift wheel 

frame fully before transporting.

TRANSPORT HAZARD

8110-00224

CAUTION

8110-00223

NOTICE

AUTOMATIC TRANSMISSION 

FLUID (ATF) ONLY

Capacity: 28 L (7.4 gal)
Use of other oil types may damage 

the equipment.

8110-00231

HIGH PRESSURE FLUID HAZARD

Hydraulic fluid can cause serious injury if it 

penetrates the skin. If it does, see a doctor 

immediately.

•  Relieve system pressure before repairing, adjusting 

or disconnecting.

•  Wear proper hand and eye protection when searching

 

for leaks. Use wood or cardboard instead of hands.

WARNING

P1513036

To prevent death or serious injury:

• Keep away from rotating cable drum and winch 

cable.

• Inspect lift cable periodically; replace if damaged.
•  Inspect cable clamps periodically; tighten if necessary.

WARNING

P1513038

To prevent serious injury or 

death, shut off power and 

reattach guard before operating 

machine.

MISSING GUARD HAZARD

WARNING

P1513008

UCX3 S-DRIVE FIELD LOADER – PORTABLE GRAIN BELT CONVEYOR

1. SAFETY

Summary of Contents for 1549



























































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands