manualshive.com logo in svg

Ag Leader GeoSteer CDMA, Operator'S Manual, Page: 53 / 102

Share
Download
Ag Leader GeoSteer CDMA Operator'S Manual Download Page 53

GeoSteer®

47 

PN 2006410—ENG Rev. B

Change Frequency

1.

Obtain the radio frequency and channel spacing used by 
the base station.

2.

Press the Change Frequency button.

3.

Manually enter a new Frequency number using the 
numeric keypad and select the proper Channel Spacing.

4.

Press the Green Check Mark to save the new frequency 
setting or press the Red X to cancel.

Use Previous

1.

Obtain the radio frequency and channel spacing used by 
the base station.

2.

Press the Use Previous button.

3.

Use the Gray Up/Down Arrows or directly select one of the 
previously used radio modem frequencies.

4.

Press the Green Check Mark to save the new frequency 
setting or press the Red X to cancel.

THROUGHPUT

The Throughput screen displays the RTK source and a graph 
showing the percentage of correction packets that is received 
by the GeoSteer system.

To access the Throughput screen, select the GPS tab from the 
main AutoSteer Setup screen, press the RTK button, and then 
select Throughput from the list on the right.

The information available in the Throughput screen is:

Current Channel

—This shows where the system is getting the 

RTK correction from. It will have one of the following values:

XXX

—XXX represents the actual Channel or Frequency the 

internal radio modem is set to.

NTRIP

—Shows this if the system is communicating with a NTRIP server.

External

—Shows this if the system is connected to an external device.

Graph

—The graph shows the quality (percentage of data packets received over time) of the real-time communication link 

between the GeoSteer system and the correction source.

Graph

÷

NOTE!: The Throughput graph only shows activity after the GeoSteer system has calculated a position for the 
vehicle. Always verify that the GeoSteer system has a vehicle position before troubleshooting communication 
issues. Even if the system does not have a position calculated and is not showing any throughput, the GeoSteer 
system may be getting information from the base station. This can be confirmed by checking if any base station 
satellite information is displaying in the Base Satellites screen.

If an obstacle blocks the signal from the base station, the radio link, or cell connection is lost for a short time, this graph will 
show this by the percentage dropping down. The graph shows the past 60 seconds of activity. For best results, the 
Throughput should be at 100%; however the GeoSteer system can continue to run in RTK Mode with a signal as low as 

Summary of Contents for GeoSteer CDMA







































































































Reviews:

No comments