manualshive.com logo in svg

Ag Leader GeoSteer CDMA, Operator'S Manual, Page: 46 / 102

Share
Download
Ag Leader GeoSteer CDMA Operator'S Manual Download Page 46

40

ENABLE (DISABLE)

To Enable or Disable Remote Switch:

1.

From System tab, press Accessories button, 
highlight Remote Switch from list on left, and 
then press Enable (Disable) button.

2.

Once Enable (Disable) button has been 
pressed, button will change to opposite of 
what it was and Current Status will be 
updated.

REMOTE SWITCH DISENGAGE

Remote Switch Disengage option allows user to connect an external device (foot switch, rocker switch, toggle switch, etc.) 
to system harness. User can then use external switch to Disengage  AutoSteer by pressing switch. This allows operator an 
easier way to Disengage AutoSteer so they do not have to reach up to the display.

Remote Switch Disengage accessory is by default disabled. Remote Switch Disengage accessory option will show user 
Current Status (Enabled or Disabled) of switch and provide user a way to change that status. This screen has one option:

Enable (Disable)

—This button switches between two states after you push it. It enables or disables Remote Switch 

Disengage Only option.

ENABLE (DISABLE)

To Enable or Disable Remote Switch Disengage:

1.

From System tab, press Accessories button, 
highlight Remote Switch Disengage from list 
on left, and then press Enable (Disable) 
button.

2.

Once Enable (Disable) button has been 
pressed, button will change to opposite of 
what it was and Current Status will be 
updated.

TECHNICIAN

Technician screen is password protected. Entry past this screen requires proper training and is only to be used by qualified 
service technicians. There are no normal operation options required by users in this screen.

SOFTWARE UPGRADE

÷

NOTE!: When using WiFi or Ethernet connection to a Tablet or Laptop Tablet or Laptop is considered display

Summary of Contents for GeoSteer CDMA







































































































Reviews:

No comments