ADTRAN Express L1.5 User Manual Download Page 92

Page: 92 / 145

Chapter 3: Terminal Menu Operation and Structure

Express L768/L1.5 User Manual

61202192L1-1

IPX Servers/Hops

- Number of routers that must go through to get to

server. Ranges from 0-15 or 16 for infinite.

IPX Servers/TTL

- Seconds until address is removed from table.

Value of 999 means server is static.

Status/WAN Stats

Read security: 5
This menu contains generic WAN statistics on HDLC hardware port.

HDLC Port

Tx Bytes

- total number of raw bytes sent out HDLC port 1

Rx Bytes

- total number of raw bytes received in HDLC port 1

Rx CRCs

- total number of CRC errors detected on HDLC port 1

Clear Counts

- When activated, clears all WAN stat counts

Status/LAN Stats

Read security: 5
This menu contains statistics for the Ethernet port.

Tx Packets

- Packets transmitted out the Ethernet port

Rx Packets

- Packets received from the Ethernet port

Tx Errors

- Total transmit errors encountered on Ethernet port

Single Collisions

- total single collisions before successful

transmission

Multiple Collisions

- total multiple collisions before successful

transmission

Excessive Collisions

- total collisions that resulted in packet being

dropped

Deferred Transmissions

- total packets deferred due to collisions

Carrier Sense Errors

- total carrier sense errors encountered (no

link integrity)

Rx Errors

- Total packets received in error and dropped

CRCs

- total packets detected with CRC errors

Giants

- total packets received that were greater than 1518 bytes

Runts

- total packets received that were less than 64 bytes

Rx Collisions

- total collision occurred during reception

Clear Counts

- When activated, clears all LAN Stat counts.

Summary of Contents for Express L1.5


















































































































































Search results

Summary of Contents for Express L1.5

Reviews:

Related manuals for Express L1.5

Brands by name

Popular brands

ADTRAN Express L1.5, User Manual

Search results

Summary of Contents for Express L1.5

Reviews:

Related manuals for Express L1.5

Brands by name

Popular brands