ADTRAN Express L1.5 User Manual Download Page 9

Page: 9 / 145

Table of Contents

61202192L1-1

Express L768/L1.5 User Manual

IP/Route ......................................................................................................... 58

Route/IP/Net.......................................................................................... 58

Route/Netmask ...................................................................................... 58

Route/Force IP ........................................................................................ 59

IP/RIP ............................................................................................................. 59

RIP/Mode ................................................................................................ 59

RIP/Protocol............................................................................................ 59

RIP/Method............................................................................................. 59

RIP/Direction .......................................................................................... 59

RIP/Triggered ......................................................................................... 60

PPP Profile/IPX ................................................................................................... 60

IPX/Mode....................................................................................................... 60

IPX/Remote Network .................................................................................. 60

IPX/Triggered ............................................................................................... 60

IPX/Type 20 Packets..................................................................................... 60

PPP Profile/Bridge .............................................................................................. 61

Bridge/Mode ................................................................................................. 61

PPP Profile/PPP................................................................................................... 61

PPP/VJ Compression ................................................................................... 61

PPP/Max Config ........................................................................................... 62

PPP/Max Timer............................................................................................. 62

PPP/Max Failure........................................................................................... 62

PPP Profile/Filters............................................................................................... 62

Filters/WAN-to-LAN (In) ........................................................................... 62

Filters/In Exceptions .................................................................................... 63

Filters/LAN-to-WAN (Out) ........................................................................ 64

Filters/Out Exceptions ................................................................................. 64

Configuration/Management ..................................................................................... 65

Management/Telnet ........................................................................................... 65

Telnet/Server Access .................................................................................... 65

Telnet/User List ............................................................................................ 66

User List/Name ...................................................................................... 66

User List/Authen Method..................................................................... 66

User List/Password................................................................................ 66

User List/Idle Time ................................................................................ 66

User List/Level ....................................................................................... 66

Management/SNMP ........................................................................................... 67

SNMP Access ................................................................................................. 67

SNMP/Communities.................................................................................... 67

Communities/Name ............................................................................. 67

Communities/Privilege ......................................................................... 67

Communities/Manager IP .................................................................... 67

SNMP/Traps.................................................................................................. 68

Traps/Manager Name ........................................................................... 68

Traps/Manager IP .................................................................................. 68

Management/Maint Port ................................................................................... 68

Maint Port/Password Protect ..................................................................... 68

Maint Port/Password................................................................................... 68

Summary of Contents for Express L1.5


















































































































































Search results

Summary of Contents for Express L1.5

Reviews:

Related manuals for Express L1.5

Brands by name

Popular brands

ADTRAN Express L1.5, User Manual

Search results

Summary of Contents for Express L1.5

Reviews:

Related manuals for Express L1.5

Brands by name

Popular brands