ADTRAN Express L1.5 User Manual Download Page 42 | Manualshive

Page: 42 / 145

background image

Chapter 3: Terminal Menu Operation and Structure

26

Express L768/L1.5 User Manual

61202192L1-1

Configuration/IP

The IP menu is used to set up the IP parameters for the Express L768/L1.5.
Any general IP-related configuration item is under this menu. Figure 3-4
shows the IP menu.

Figure 3-4

Configuration/IP Screen

IP/IP Address

Write security: 2; Read security: 5
The IP address assigned to the Express L768/L1.5’s Ethernet port is set here.
This address must be unique within the network. Factory default is 10.0.0.1.

IP/Subnet Mask

Write security: 2; Read security: 5
The IP network mask to be applied to the Express L768/L1.5’s Ethernet port is
set here. Factory default is 255.255.255.0.

IP/Default Gateway

Write security: 3; Read security: 5
The default gateway is used by the Express L768/L1.5 for sending IP packets

«
...
40
41
42
43
44
...
»

Summary of Contents for Express L1.5


















































































































































Reviews:

No comments

Related manuals for Express L1.5

Brand: CAME Pages: 19

Brand: Ubiquiti Pages: 40

Brand: Paradyne Pages: 2

Brand: Paradyne Pages: 20

Brand: Paradyne Pages: 2

Brand: Zhone Pages: 2

COMSPHERE 6800 Series

Brand: Paradyne Pages: 155

COMSPHERE 6800 Series

Brand: Paradyne Pages: 44

Brand: Q-See Pages: 2

Brand: Draytek Pages: 8

Brand: FS Pages: 19

Brand: EMCIS Pages: 14

Brand: Intel Pages: 958

SUPERSERVER 6027TR-H71FRF

Brand: Supero Pages: 118

EtherLink 3C905C-TX

Brand: 3Com Pages: 96

Brand: Intercoax Pages: 2

Brand: SainSmart Pages: 12

Brand: Wave wifi Pages: 3

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands