ADTRAN Express L1.5 User Manual Download Page 5

Page: 5 / 145

61202192L1-1

Express L768/L1.5 User Manual

Table of Contents

Quick Startup Guide ........................................................................................................ 1

Setting up the HDSL Line ................................................................................................. 1

Chapter 1. Understanding HDSL and the Express L768/L1.5 ................................... 3

HDSL Overview ................................................................................................................. 3

The Express L768/L1.5 ...................................................................................................... 4

Applications ................................................................................................................. 5

Single User to Corporate LAN .................................................................... 5

Frame Relay Connectivity to ADTRAN Frame Port 768......................... 6

Small Office - Home Office (SOHO) to Corporate LAN.......................... 7

Routing and Bridging with the Express L768/L1.5................................................ 8

Factory Default..................................................................................................... 8

Bridging................................................................................................................. 8

IP Routing ............................................................................................................. 9

IPX Routing........................................................................................................... 9

Concurrent Routing And Bridging ........................................................................... 9

Network Address Translation Mode........................................................................ 9

Front Panel.................................................................................................................... 10

Indicators............................................................................................................... 10

Rear Panel ..................................................................................................................... 11

Configuration ............................................................................................................... 11

Security.......................................................................................................................... 12

Chapter 2. Installation ...................................................................................................... 13

HDSL Network Connection.............................................................................................. 13

T1 Overview ................................................................................................................. 13

HDSL Overview........................................................................................................... 13

Local Area Network Connection ..................................................................................... 14

Chapter 3. Terminal Menu Operation and Structure ................................................. 15

Terminal Menu Structure.................................................................................................. 15

Configuration ............................................................................................................... 15

Status ............................................................................................................................. 17

Test................................................................................................................................. 17

Logs................................................................................................................................ 17

Utilities .......................................................................................................................... 17

Navigating the Terminal Menus ...................................................................................... 18

General Layout............................................................................................................. 18

Menu Path..................................................................................................................... 18

Moving Around ........................................................................................................... 18

Submenus [+] or [DATA] ............................................................................. 18

Activation Field <+> ..................................................................................... 18

Editable Data Field........................................................................................ 18

Summary of Contents for Express L1.5


















































































































































Search results

Summary of Contents for Express L1.5

Reviews:

Related manuals for Express L1.5

Brands by name

Popular brands

ADTRAN Express L1.5, User Manual

Search results

Summary of Contents for Express L1.5

Reviews:

Related manuals for Express L1.5

Brands by name

Popular brands