ADTRAN Express L1.5 User Manual Download Page 105

Page: 105 / 145

61202192L1-1

Express L768/L1.5 User Manual

Appendix A

Loop Status Messages

The Express L768/L1.5 displays current loop status of the HDSL on the bottom
center line of the terminal screen. The following messages are defined:

Connected

This is seen when the Express L768/L1.5 HDSL layer 1 is up. The rate is de-
termined by what it is configured for under

Configuration/WAN/HDSL/Rate

Echo: Tx: X Rx: Y

The current transmit and receive count for the PPP echo request test.

Layer 1 up

The Express L768/L1.5’s HDSL layer 1 is up.

Link down

The HDSL link is not synchronized.

Link In Sync

The HDSL link is synchronized but layer 1 is not up.

NET EOC LOOPBACK

Express L768/L1.5 has received an HDSL EOC loopback command from the
far end.

RINGING

An incoming call is ringing.

Rate Status Messages

Displays the rate at which the connection has been established.

Summary of Contents for Express L1.5


















































































































































Search results

Summary of Contents for Express L1.5

Reviews:

Related manuals for Express L1.5

Brands by name

Popular brands

ADTRAN Express L1.5, User Manual

Search results

Summary of Contents for Express L1.5

Reviews:

Related manuals for Express L1.5

Brands by name

Popular brands