background image

 

FCC regulations require that the following information be provided in this manual:

1. If this equipment

 

 

 

causes harm to the telephone network, the telephone company 

may temporarily discontinue service.  If possible, advance notification is given; oth-

erwise, notification is given as soon as possible.  The telephone company will advise 

the customer of the right to file a complaint with the FCC.

2. The telephone company may make changes in its facilities, equipment, operations, 

or procedures that could affect the proper operation of this equipment; advance no-

tification and the opportunity to maintain uninterrupted service are given. 

3. If experiencing difficulty with this equipment,

 

 

 

please contact ADTRAN

 

 

 

(see inside 

back cover)

 

 

 

for repair and warranty information.  The telephone company may re-

quire this equipment to be disconnected from the network until the problem is cor-

rected, or it is certain the equipment is not malfunctioning.

4. This unit contains no user serviceable parts.

To ADTRAN service personnel: For continued protection against risk of fire, 

replace F1 with the same type and rating of fuse only: .2A, 250 V.

 

FEDERAL COMMUNICATIONS COMMISSION

RADIO FREQUENCY INTERFERENCE STATEMENT

 

This equipment has been tested and found to comply with the limits for a Class A dig-

ital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a residential environment. This

equipment generates, uses, and can radiate radio frequency energy and, if not installed

and used in accordance with the instructions, may cause harmful interference to radio

or TV reception, which can be determined by turning the equipment off and on.  The

user is encouraged to try to correct the interference by one or more of the following

measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to 
which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

 

Changes or modifications to this unit not expressly approved by ADTRAN will void 

the user's authority to operate the equipment.

Summary of Contents for Express L1.5


















































































































































Reviews: