ADTRAN Express L1.5 User Manual Download Page 103

Page: 103 / 145

61202192L1-1

Express L768/L1.5 User Manual

Chapter 4

Specifications

SPECIFICATIONS AND FEATURES

This section describes the standard specifications and features incorporated in
the Express L768/L1.5.

Network Interface

•

RJ-45 for HDSL two-wire (Express L768) or four-wire (Express L1.5) ser-
vice.

•

Signal Format: 2B1Q

•

Max distance per loop: 8000 feet at 26 AWG

Ethernet Interface (LAN)

Ethernet/IEEE 802.3 10BaseT.

Display

Available through terminal interface or Telnet session

Environmental

•

Operating Temperature: 0 - 50

•

Storage Temperature: 20 - 70

•

Relative Humidity: Up to 95% non-condensing

Physical

•

Dimensions: 1 1/2" H x 9" W x 6 1/4" D

•

Weight: 9.5 oz.

Power

•

120 VAC, 60 Hz, 8 W typical

Summary of Contents for Express L1.5


















































































































































Search results

Summary of Contents for Express L1.5

Reviews:

Related manuals for Express L1.5

Brands by name

Popular brands

ADTRAN Express L1.5, User Manual

Search results

Summary of Contents for Express L1.5

Reviews:

Related manuals for Express L1.5

Brands by name

Popular brands