ADTRAN Express L1.5 User Manual Download Page 87

Page: 87 / 145

Chapter 3: Terminal Menu Operation and Structure

61202192L1-1

Express L768/L1.5 User Manual

Status/Sessions

This menu contains the current status of all sessions and spanning tree ports.

Sessions/PPP Session

Read security: 5
This menu reflects the results of PPP negotiations, user name, time connected,
and data rates for the session.

PPP Links

- Reflects LCP layer active

BCP

- Shows UP if PPP Bridge Control Protocol has negotiated

successfully

IPCP

- Shows UP if PPP IP Control Protocol has negotiated

successfully

IPXCP

- Shows UP if PPP IPX Control Protocol has negotiated

successfully

Up Time

- Displays how long the call has been connected

Tx Pkts

- Number of packets transmitted

Rx Pkts

- Number of packets received

Tx Bytes

- Number of bytes transmitted

Rx Bytes

- Number of bytes received

Tx Rate

- Current application data transmission rate

Rx Rate

- Current application data reception rate

Summary of Contents for Express L1.5


















































































































































Search results

Summary of Contents for Express L1.5

Reviews:

Related manuals for Express L1.5

Brands by name

Popular brands

ADTRAN Express L1.5, User Manual

Search results

Summary of Contents for Express L1.5

Reviews:

Related manuals for Express L1.5

Brands by name

Popular brands