ADTRAN Express L1.5 User Manual Download Page 113

Page: 113 / 145

Appendix B: Log Messages

61202192L1-1

Express L768/L1.5 User Manual

Telnet Session Closed

level 4
Telnet server has closed connection.

Telnet Session failed, error <errnum>

level 2
Telnet server could not connect to Telnet client due to error.

TELNETD: accept failed

level 2
Telnet server could not open TCP socket to incoming Telnet client.

TELNETD: Set TCPC_LISTENQ failed

level 6
Debugging message related to Telnet server function.

TELNETD: Clr TCBF_BUFFER flag failed

level 6
Debugging message related to Telnet client function.

TELNETD: could not obtain peer ip

level 2
Telnet server function could not get IP address of Telnet client.

TELNETD: Session failed, error

level 2
A Telnet server session has failed because of an error.

TELNETD: Set TCBF_DONTBLOCK flag failed

level 6
Debugging message related to Telnet client function.

TELNETD: SOCKET creation error

level 2
Telnet server could not be started due to TCP socket error.

TFTP: can't get to host

level 2
TFTP client could not get to host.

Summary of Contents for Express L1.5


















































































































































Search results

Summary of Contents for Express L1.5

Reviews:

Related manuals for Express L1.5

Brands by name

Popular brands

ADTRAN Express L1.5, User Manual

Search results

Summary of Contents for Express L1.5

Reviews:

Related manuals for Express L1.5

Brands by name

Popular brands