ADB Safegate IDM 8000 User Manual Download Page 73

Page: 73 / 118

7.0 Troubleshooting

Warning!

High voltage present! Only qualified personnel should do troubleshooting!

If the CCR has tripped because of input voltage, frequency or temperature failure it is possible that it starts automatically when

the mains returns to accepted values!

Remember to check the fault indication and the fault log before troubleshooting.

7.1 CCR Does Not Start

Check / observe

Probable cause / corrective action

Man.ref

Ok led off on the power unit

Check main switch position.

Check mains values

Check fuses

Check supply transformer T2

1.3.2 Power circuit

Check / replace the power unit

1.3.5 Control unit

LCD display shows no main menu and display

backlight is not on after start-up.

Check DC voltages from A1 motherboard connector X7-3

(+5V) X7-4 (+12V) X7-5 (-12V) X7-6 (GND)

Replace power unit (if no power).

Replace LCD unit (if power ok).

LCD display shows no main menu and display

backlight is on after start-up.

Check display contrast. If not enough, remove four screws

that hold the LCD display in place. Adjust from Ccal

trimmer, until display visible.

Replace LCD unit (if contrast not visible).

Replace MCU unit (if contrast visible).

2.6.11 LCD contrast setting

After change of MCU control unit or LCD display

unit LCD display appears shifted.

Press F1 and F5 simultaneously for 5 seconds.

Replace MCU control unit (if shift does not go away)

U1 –A or U1 +A on display

Check mains voltage level

Check U1 calibration

2.4.2 Input voltage U1

calibration

Check U1 nom setting

2.5.4 Input voltage

protection and 2.6.7

Hardware system settings

Check sync transformer

Freq. A- or Freq. A+ on display

Check mains frequency level

Check f1 nom setting

2.5.5 Input frequency and

temperature setting and

2.6.7 Hardware system

settings

Check sync transformer

Temp A1 on display

Check the temperature value from View / E/T.

2.5.5 Input frequency and

temperature setting

Check that ventilation is not blocked.

1.3.1 General

Check temperature sensor on the thyristor cooling element.

E fault A or B on display * only if maintenance

switch function is used.

Check if Earth fault maintenance switch is on and earth

fault level B is reached. If no real earth fault exists check

earth fault calibration and set levels.

2.1 Control functions,

2.4.4 Earth fault calibration,

2.6.3 Earth fault setting

UM_IDM-8000, Rev. 1.7, 2021/05/06

Summary of Contents for IDM 8000







































































































Search results

Summary of Contents for IDM 8000

Reviews:

Brands by name

Popular brands

ADB Safegate IDM 8000, User Manual

Search results

Summary of Contents for IDM 8000

Reviews:

Brands by name

Popular brands