ADB Safegate IDM 8000 User Manual Download Page 70

Page: 70 / 118

Check and adjust/test (if desired) the earth fault alarm levels and maintenance switch

setting.

2.6.3 Earth fault setting

Calibrate earth fault monitor and test.

2.4.4 Earth fault calibration

Connect the output terminals to operating mode ”normal” after the calibration.

1.3.4 High voltage circuit

Check and adjust/test (if desired) the lamp fault alarm levels and FAA switch.

2.6.2 Lamp fault setting

Check and adjust/test (if desired) the current fault alarm levels.

2.6.5 Current fault setting

Check and adjust/test (if desired) the VA drop alarm settings.

2.6.4 VA-Drop setting

Calibrate lamp fault monitor. Write down LF lim. 1.74…3.50A.

2.4.3 Lamp fault and VA-Drop

calibration

10.

Check and test (if desired) the remote control function according to remote control

manual.

11.

Fill up the commissioning test report in Appendix I and sign all sheets. Store the diary and

all documents inside the CCR.

Appendix I – Commissioniong test

report form

All the CCRs have been factory tested and have factory settings, which in most cases can be used for the project, already set.

IDM 8000
Installation

58
Copyright

Summary of Contents for IDM 8000







































































































Search results

Summary of Contents for IDM 8000

Reviews:

Brands by name

Popular brands

ADB Safegate IDM 8000, User Manual

Search results

Summary of Contents for IDM 8000

Reviews:

Brands by name

Popular brands