ADB Safegate IDM 8000 User Manual Download Page 59

Page: 59 / 118

Displays with parallel remote control card or no card detected:

Header / function

Data 1

Data 2

Fact set

Allowed range

Remote control set

Serial/parallel cntrl

RCMODE

Auto detect: parallel / none

Signal coding

Dec/Bin

Dec

Dec/bin

Signal mode

Cont/imp

Cont

Cont / imp

Com fault content

ComF-m

SysF

SysF / SumF

Setting sequence

1. Set the control switch in Off-position.

1. Go to remote control settings by selecting Set /Set /More/Rcs.

1. Browse the desired parameter with Next, adjust it with , + / - and select Set to confirm.

4.6.10 Circuit selector minimum current setting

This setting defines the reduced output current of the CCR when disconnecting loads with the circuit selector. Optimal setting

causes minimum flickering of lights without overshooting the output current when disconnecting loads with the circuit

selector.

Note

: Factory setting is minimum current with short circuit load. If more than one circuit is active, ERR indication is displayed.

Header / function

Data 1

Data 2

Fact set

Allowed range

Set Cs min current

I2 / A

CS MIN

Short

Loads CS1-CS4 (only one)

Set / Min

Setting sequence

1. Select the smallest of the circuit selector loads CS1-CS4. Use U2 View display to check which one is smallest (smallest U2 means smallest

load).

1. Select Set/Set/More/CSI to go to circuit selector minimum current setting

1. Select the desired current level with the local operation switch e.g. step 6.

1. Select Set to store the setting into memory and select Min to reset to a safe value.

UM_IDM-8000, Rev. 1.7, 2021/05/06

Summary of Contents for IDM 8000







































































































Search results

Summary of Contents for IDM 8000

Reviews:

Brands by name

Popular brands

ADB Safegate IDM 8000, User Manual

Search results

Summary of Contents for IDM 8000

Reviews:

Brands by name

Popular brands