ADB Safegate IDM 8000 User Manual Download Page 16

Page: 16 / 118

1.1.6 Maintenance Safety

DANGER

Electric Shock Hazard

This equipment may contain electrostatic devices

• Do not operate a system that contains malfunctioning components. If a component malfunctions,

turn the system OFF immediately.

• Disconnect and lock out electrical power.
• Allow only qualified personnel to make repairs. Repair or replace the malfunctioning component

according to instructions provided in its manual.

Failure to follow these instructions can result in death or equipment damage

1.1.7 Material Handling Precautions, ESD

CAUTION

Electrostatic Sensitive Devices

This equipment may contain electrostatic devices

• Protect from electrostatic discharge.
• Electronic modules and components should be touched only when this is unavoidable e.g. soldering,

replacement.

• Before touching any component of the cabinet you shall bring your body to the same potential as the

cabinet by touching a conductive earthed part of the cabinet.

• Electronic modules or components must not be brought in contact with highly insulating materials

such as plastic sheets, synthetic fiber clothing. They must be laid down on conductive surfaces.

• The tip of the soldering iron must be grounded.
• Electronic modules and components must be stored and transported in conductive packing.

Failure to follow this instruction can result in equipment damage

IDM 8000
Safety

4
Copyright

Summary of Contents for IDM 8000







































































































Search results

Summary of Contents for IDM 8000

Reviews:

Brands by name

Popular brands

ADB Safegate IDM 8000, User Manual

Search results

Summary of Contents for IDM 8000

Reviews:

Brands by name

Popular brands