ADB Safegate IDM 8000 User Manual Download Page 36

Page: 36 / 118

4.2.1 Display Interface Main Menu Structure

The main menu has three selections:

•

View Viewing the values without affecting any set values.

•

Cs Circuit selector control (only if the CCR is defined as a circuit selector CCR).

•

Set CCR calibration and setting functions. Password protection of settings menu is selectable from the Sys settings.

Factory setting for password protection is not in use (Off).

4.2.2 The set menu is divided into 3 sub menus:

•

Cal Calibrating functions

•

Prot Protective functions; monitoring functions which are able to trip the CCR

•

Set Setting functions; other monitoring and system configuration functions

4.2.3 Commonly used symbols in all display menus:

•

More Brings more equal level displays

•

Up Brings you back to upper level display

4.3 View functions

IDM 8000
User Interface

24
Copyright

Summary of Contents for IDM 8000







































































































Search results

Summary of Contents for IDM 8000

Reviews:

Brands by name

Popular brands

ADB Safegate IDM 8000, User Manual

Search results

Summary of Contents for IDM 8000

Reviews:

Brands by name

Popular brands