ADB Safegate IDM 8000 User Manual Download Page 41

Page: 41 / 118

U1 calibration

1. Connect external calibrated V-meter (appropriate scale, accuracy better than 1%) to the CCR mains input terminals (main switch).

Warning!

Line voltage circuit – use appropriate test probes!

1. Go to /U1 calibration: select Set/Cal/ In.

1. Adjust the U1 reading on data 1 to equal with the external meter reading.

1. Make sure that the readings are equal then select Set.

1. Check View/In that both readings are equal, if necessary repeat steps 3-5.

Note : Calibration for DC1 (+5V), DC2 (+12V) and DC3 (-12V) system voltages also provided in this display. Factory settings: not necessary to

calibrate during commissioning.

4.4.3 Lamp Fault and VA-Drop Calibration

Header / function

Data 1

Data 2

Remarks

Lamp fault cal

I2 / A (Fact set 2,80A)

Lflim

+ - adjust, Set, Next

Measured LF voltage

Lfcal = 0

Run steps 1-7 and set, Next

Qty of real lamp faults

Lfcal > 0

+ - adj. Run 1-7,Set

Lamp Fault and VA-drop calibration

1. Make sure that there are no lamp faults in the circuit.

Note : All isolation transformers must be of the same size and make in order to

achieve the full accuracy of the lamp fault monitoring function.

1. Go to lamp fault calibration, select Set/Cal/Lf.

1. If necessary adjust Lflim value (factory setting 2.80A for typical trafos) then select Next.

1. Start the CCR and control from Datafield 1 the measurement value to be below 0.8 on all steps. To adjust the value, change the Lflim

value between 1.75A and 3.50A, re-check the measurement value. To calibrate, start the CCR with step 1, wait 30 seconds and select Set.

Note : For circuit selector CCRs ensure that all circuits are selected. Lamp fault monitoring function will only activate when all circuits are

selected.

1. Increase the brilliancy step, wait 30 s and select Set. Repeat this until step 7 is set.

Note : VA-drop full load values are automatically

calibrated at the same time.

Warning!

High voltage circuit - De-energize CCR before working with the load

circuit!

1. Arrange desired amount of real lamp faults to the circuit.

Note : Use either level A amount of lamp faults or not less than 2 or more than

7 is required.

Warning!

High voltage circuit – De-energize CCR before working with the load

circuit!

UM_IDM-8000, Rev. 1.7, 2021/05/06

Summary of Contents for IDM 8000







































































































Search results

Summary of Contents for IDM 8000

Reviews:

Brands by name

Popular brands

ADB Safegate IDM 8000, User Manual

Search results

Summary of Contents for IDM 8000

Reviews:

Brands by name

Popular brands