ADB Safegate IDM 8000 User Manual Download Page 63

Page: 63 / 118

Tip

Define a fixed time interval for inspection.

2. Do the following after a long storage period:

•

Clean the equipment, if necessary.

•

Remove the oxidation layer from the electrical contact before connection, if necessary.

5.1.3 Moving and Handling the CCR at Site

10 cm elevation of the bottom plate is provided to enable use of forklifts.
Keep the CCR always in upright position as it contains heavy components and fixing is designed for upright position only.

5.1.4 Installation Requirements

Fast path

Make sure that you install the CCR in a well-ventilated environment with sufficient clearances to walls and other

objects. This way you ensure proper ventilation and smooth workflows in case of operation / maintenance tasks.

Table 2: Heat dissipation for air conditioning calculation

Version

Value (W)

3 kVA

300 W

4 kVA

400 W

5 kVA

500 W

7.5 kVA

750 W

10 kVA

1000 W

12.5 kVA

1250 W

15 kVA

1400 W

17.5 kVA

1500 W

20 kVA

1600 W

25 kVA

2000 W

30 kVA

2400 W

5.2 Mechanical Installation

•

All cable entries are through the bottom plate of the CCR.

•

Leave 20cm clearance from wall and 50cm between CCR rows (back to back installation) for proper ventilation space.

•

Reserve sufficient clearance in the front of the CCR for maintenance and operation purposes.

5.3 Electrical Installation

UM_IDM-8000, Rev. 1.7, 2021/05/06

Summary of Contents for IDM 8000







































































































Search results

Summary of Contents for IDM 8000

Reviews:

Brands by name

Popular brands

ADB Safegate IDM 8000, User Manual

Search results

Summary of Contents for IDM 8000

Reviews:

Brands by name

Popular brands